100% Original Factory Pipe Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex


Product Detail

Product Tags

Related Video

Feedback (2)

Assume full accountability to fulfill all demands of our purchasers; attain continual advancements by marketing the advancement of our clientele; grow to be the final permanent cooperative partner of purchasers and maximize the interests of purchasers for Return Air Duct Insulation , Class 0 Fire Rating Materials , Chilled Water Pipe Insulation , Base on the business concept of Quality first, we would like to meet more and more friends in the word and we hope provide the best product and service to you.
100% Original Factory Pipe Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex Detail:

Uses

KingWrap provides a fast, easy method of insulating pipes and fittings. It is used to control condensation drip on domestic cold-water, chilled-water, and other cold piping bond with metal surfaces. On cold piping and fittings and to reduce heat loss when applied to hot-water lines that will operate up to 180°F(82°C). KingWrap may be used in conjunction with Kingflex Pipe and Sheet Insulation. Its greatest advantage, however, is the ease with which it can be used to insulate short lengths of pipe and fittings in congested or hard-to-reach areas.

Application Instructions

KingWrap is applied by removing release paper as the tape is spirally bond with metal surfaces. On cold piping, the number of wraps required must be sufficient to keep the outer insulation surface above the dew point of the air so that sweating will be controlled. On hot lines, the number of wraps is dictated only by the amount of heat loss control that is desired. On dual-temperature lines, any number of wraps sufficient to control sweating on the cold cycle is usually adequate for the heating cycle.

Multiple wraps are recommended. Tape should be applied with a spiral wrap to obtain a 50% overlap. Additional layers are added to build up insulation to the required thickness.

To insulate valves, tees, and other fittings, small pieces of tape should be cut to size and pressed into place, with no metal exposed. The fitting then is additionally over-wrapped with longer lengths for a durable and efficient job.

Kingflex provides this information as a technical service. To the extent the information is derived from sources other than Kingflex, Kingflex is substantially, if not wholly, relying upon the other source(s) to provide accurate information. Information provided as a result of Kingflex’s own technical analysis and testing is accurate to the extent of our knowledge and ability, as of date of printing, using effective standardized methods and procedures. Each user of these products, or information, should perform their own tests to determine the safety, fit-ness and suitability of the products, or combination of products, for any foresee-able purposes, applications and uses by the user and by any third party to which the user may convey the products. Since Kingflex cannot control the end use of this product, Kingflex does not guarantee that the user will obtain the same results as published in this document. The data and information are provided as a technical service and are subject to change without notice.


Product detail pictures:

100% Original Factory Pipe Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex detail pictures

100% Original Factory Pipe Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex detail pictures

100% Original Factory Pipe Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex detail pictures


Related Product Guide:

Our company insists all along the quality policy of "product good quality is base of enterprise survival; buyer fulfillment will be the staring point and ending of an company; persistent improvement is eternal pursuit of staff" and also the consistent purpose of "reputation very first, shopper first" for 100% Original Factory Pipe Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex , The product will supply to all over the world, such as: Zambia, San Francisco, Mumbai, We have been making our products for more than 20 years . Mainly do wholesale , so we have the most competitive price , but highest quality. For the past years , we got very good feedbacks , not only because we provide good products , but also because of our good after-sale service . We are here waiting for you for your inquiry.
  • In our cooperated wholesalers, this company has the best quality and reasonable price, they are our first choice.
    5 Stars By Quintina from Philippines - 2017.11.20 15:58
    We are old friends, the company's product quality has been always very good and this time the price is also very cheap.
    5 Stars By Penny from Canada - 2018.09.29 13:24