Manufacturing Companies for Ac Tube Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex


Product Detail

Product Tags

Related Video

Feedback (2)

Our eternal pursuits are the attitude of "regard the market, regard the custom, regard the science" and the theory of "quality the basic, trust the first and management the advanced" for Advanced Insulation Solutions North East , Pipe Insulation Material , Ac Pipe Insulation Foam , Please sense no cost to speak to us anytime. We are going to reply you when we receive your inquiries. Remember to note that samples are available before we start our business enterprise.
Manufacturing Companies for Ac Tube Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex Detail:

Uses

KingWrap provides a fast, easy method of insulating pipes and fittings. It is used to control condensation drip on domestic cold-water, chilled-water, and other cold piping bond with metal surfaces. On cold piping and fittings and to reduce heat loss when applied to hot-water lines that will operate up to 180°F(82°C). KingWrap may be used in conjunction with Kingflex Pipe and Sheet Insulation. Its greatest advantage, however, is the ease with which it can be used to insulate short lengths of pipe and fittings in congested or hard-to-reach areas.

Application Instructions

KingWrap is applied by removing release paper as the tape is spirally bond with metal surfaces. On cold piping, the number of wraps required must be sufficient to keep the outer insulation surface above the dew point of the air so that sweating will be controlled. On hot lines, the number of wraps is dictated only by the amount of heat loss control that is desired. On dual-temperature lines, any number of wraps sufficient to control sweating on the cold cycle is usually adequate for the heating cycle.

Multiple wraps are recommended. Tape should be applied with a spiral wrap to obtain a 50% overlap. Additional layers are added to build up insulation to the required thickness.

To insulate valves, tees, and other fittings, small pieces of tape should be cut to size and pressed into place, with no metal exposed. The fitting then is additionally over-wrapped with longer lengths for a durable and efficient job.

Kingflex provides this information as a technical service. To the extent the information is derived from sources other than Kingflex, Kingflex is substantially, if not wholly, relying upon the other source(s) to provide accurate information. Information provided as a result of Kingflex’s own technical analysis and testing is accurate to the extent of our knowledge and ability, as of date of printing, using effective standardized methods and procedures. Each user of these products, or information, should perform their own tests to determine the safety, fit-ness and suitability of the products, or combination of products, for any foresee-able purposes, applications and uses by the user and by any third party to which the user may convey the products. Since Kingflex cannot control the end use of this product, Kingflex does not guarantee that the user will obtain the same results as published in this document. The data and information are provided as a technical service and are subject to change without notice.


Product detail pictures:

Manufacturing Companies for Ac Tube Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex detail pictures

Manufacturing Companies for Ac Tube Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex detail pictures

Manufacturing Companies for Ac Tube Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex detail pictures


Related Product Guide:

Our company insists all along the quality policy of "product good quality is base of enterprise survival; buyer fulfillment will be the staring point and ending of an company; persistent improvement is eternal pursuit of staff" and also the consistent purpose of "reputation very first, shopper first" for Manufacturing Companies for Ac Tube Insulation - elastomeric NBR/PVC rubber foam thermal insulation tape – Kingflex , The product will supply to all over the world, such as: Honduras, Albania, Lesotho, Our company has built stable business relationships with many well-known domestic companies as well as oversea customers. With the goal of providing high quality products to customers at low cots, we've been committed to improving its capacities in research, development, manufacturing and management. We have honored to receive recognition from our customers. Till now we have now passed ISO9001 in 2005 and ISO/TS16949 in 2008. Enterprises of "quality of survival, the credibility of development" for the purpose, sincerely welcome domestic and foreign businessmen to visit to discuss cooperation.
  • We feel easy to cooperate with this company, the supplier is very responsible, thanks.There will be more in-depth cooperation.
    5 Stars By Julia from Qatar - 2017.06.29 18:55
    We feel easy to cooperate with this company, the supplier is very responsible, thanks.There will be more in-depth cooperation.
    5 Stars By Diana from Rotterdam - 2017.09.29 11:19